- Mechanical Seal
- Sanitary Flow Equipment
- Vacuum, Blowers And Compressor Pumps
- Rotary Vane Vacuum Pumps, Oil-Free
- Radial Blowers
- Liquid Ring Vacuum Pump
- Roots Blowers, Bora
- Centralised System
- Dry Vacuum Pumps
- Gas Ejectors
- Liquid Ring Compressors
- Liquid Ring Vacuum Pump in Compact Design
- Liquid Ring Vacuum Pump with Auto recirculation System
- Liquid Ring Vacuum Pumps in Bare Shaft Design
- Radial Vacuum Pumps
- Rotary Vane Compressor
- Rotary Vane Vacuum Pumps, Oil-Lubricated
- Screw Compressor
- Screw Vacuum Pumps
- Side Channel Ring Blowers
- Side Channel Vacuum Pumps
- View All
- Centrifugal Pump 1
- Positive Displacement Pumps
- Simple Application Pumps
- Tank Cleaning Equipment
- Centrifugal Pump 2
- Dual Disc Pump
- Engineered Systems
- Ex-Proof Motors
- Liquid Pump
- Industrial Standard Pumps in Compact Design
- Chemical Process Pumps
- Heat Transfer Pumps for Hot Oil
- Heat Transfer Pumps for Hot Water
- High Pressure Pumps
- Hygienic Liquid Pumps
- Industrial Standard Pumps in Bare Shaft Design
- Industrial Standard Pumps in Inline Design
- Side Channel Pumps in Bare Shaft Designs
- Side Channel Pumps in Compact Designs
- Side Channel Pumps in Inline Design
- Sludge Mixers
- View All
- Single Disc Pumps
- Sliding Vane Pumps
- Accessories
- Others
1, Jalan Serendah 26/41,
Hicom Industrial Estate,
40400 Shah Alam,
Selangor, Malaysia.
Bandar Perda,
14000 Bukit Mertajam,
Penang, Malaysia.


Taman Iskandar,
80050 Johor Bahru,
Johor, Malaysia.


HCMC Office:
Binh Thanh Dist.,
HCMC, Vietnam.


Ha Noi Office:
E16, 4th Flr, Sun Anrora Building
No 3, Luong Yen Street, Bach Dang Ward, Hai Ba Trung Dictrict, Ha Noi, Vietnam.

PT Kampak Peralatan Aliran
JL. Raya Perjuangan
No. 8, Kebun Jeruk
Jakarta Barat,
Jakarta 11530, Indonesia.


Gunclean Toftejorg i40 D
Previous | 3 / 4 | Next |
Alfa Laval’s Gunclean Toftejorg i40 D is a high-impact, tank cleaning machine with dual nozzles. Its reliable operation and wear-resistant design make it suitable for use in all types of tank cleaning applications. Developed to meet the toughest tank cleaning requirements, it features a hysteresis clutch with built-in speed adjustment.
This innovative clutch construction is a substantial improvement over standard magnetic clutches, as it eliminates both slippage and the leakage risk of a speed adjustment shaft. In combination with optimized design and new, wear-resistant materials, it makes the Gunclean Toftejorg i40 D a simple and reliable choice for cost-effective operation.
How it works
A flow of cleaning media or product is used to drive a turbine connected to the Gunclean Toftejorg i40 D gear unit. Rotation speed can be adjusted during operation, thus making it possible to optimize the cleaning cycle.
In the first cycle, the nozzles lay out a coarse pattern on the tank surface. The following cycles make the pattern gradually more dense until a full pattern is reached after 4 cycles.
![]() |
![]() |
Course pattern after 1 cleaning cycle |
Dense pattern after 4 cleaning cycles |
Unique hysteresis clutch
Use of a hysteresis clutch on the Gunclean Toftejorg i40 D means there is no need for the conventional configuration with a speed adjustment shaft at the turbine. This does away with shaft penetration at this key point, eliminating a key location for potential seal leaks and cross-contamination problems.
The unique clutch used on this model compromises a number of strong magnets and a hysteresis plate. Unlike a standard magnetic clutch in which two opposing magnets must be synchronized, this type does not suffer from slippage, thus eliminating false starts. The clutch also works as a soft starter, making sure the tank cleaning machine always begins operating as intended.
Nozzle rotation speed
The rotation speed of the nozzles is preset from our factory to a speed which is applicable for most cleaning operations. The rotation speed is very easy changed by adjusting a magnet which serves as a brake. The distance between the magnet and the hysteresis plate is simply increased or decreased in order to change the speed. Access to the magnet is attained by removing the cover of the gearbox